The High Pinion diff uses and is best suited for front solid axle applications. The kit, yes, spacers no. Rusted even worse but a bit sturdier. Of course, with an absolutely cherry interior and relatively rust free body, its new owner is already getting quite a few unsolicited offers, one of which has come from none other than my brother, who is absolutely chomping at the bit to get this truck. I much preferred my older 20r solid axle truck with the double chain. Stuff in red is what I plan on using, stuff in yellow is what is on it now. You should see some of the Toyotas that are still running — amazingly.
This puts it in the lowest license plate rate bracket in my state, but only by 2 lbs! The R tranny may be acessable but the 70-series landcruiser is a Canada thing. Engines For Sale: Live Auction Listings. Fugured it was a 4. I can reach out of the open rear window ro snug up the straps, or I can hop out and kift a corner and snug up that strap as needed. Prerunners are often modified two wheel drive models to save money.
I know they were also available with turbodiesel. The truck was a 2wd single cab with the long bed. The wheel spinning technique should give good information with good technique. Finding a 78 series transfercase isn't going to be as easy read: cheap as using the stuff you already have. I wan't as little down time as possible.
A stick shift and 4wd make me wish I had owned it for the past 15 or so years. They are attached to 4 bicycle hooks screwed in the rafters of my garage. The pinion or companion flange nut takes a 30mm socket. To start viewing messages, select the forum that you want to visit from the selection below. This will be a nice addition too because it has no power steering right now. All corporate trademarks are the property of their respective owners. This is one reason why I chose to use the open front windows for the forward support bar as there is no way for me alone to slide a support bar under the shell in front until it is lifted.
Toyota Tech: Pickup and 4Runner Part Specifications Welcome to 4x4Wire! For example, if the normal cut gear was designed for a 4000 lb. The Truck Index does not indicate the weight difference between the engines. You may have to before you can post: click the register link above to proceed. So the valve would shoot into the cylinder and cause lots of damage. In 1979, the spartan interior was given much more in the way of comfort; a four wheel drive model was also brought out it had a four-speed manual rather than the usual five-speed. Because, the ring gear in an open differential turns at the average speed of the two axle shafts connected to it.
Jynx: Thanks for the specs, I will go out tomarrow and dig out some of my parts and get some more measurments to see how things will line up. Breakage of the shafts is the probable result of overloading. After having a few of these though a person gets pretty sick of the single row timing chain as it seems only the factory ever got them right and no one could repair them as the head had to come off to do it right and it was likely the bearings had been subjected to an anti freeze wash. Great clutch and has 95,000 on it and still grabs tough. Make sure you reinforce the front frame rails good since, I think, the 2wd frames are a little lighter on the front than the 4wd.
While it shares internals with the V6 diff, the gears are unique to the High Pinion due to the reverse cut, which puts the gears on the drive side of the teeth in the front axle. Through the early 1980s, the Hi-Lux used a solid-axle front and rear suspension, with rear leaf springs. The old leaf rear suspension was kept with minor changes. It does not work on the 22R-E which has a shorter deck height and thus a different length chain. The post 1985 engine version was then in production for quite some time. The beds rotted out similar to the picture above, and the red one was two different colors of red due to the beds being made of a different grade of steel than the cabs and being mounted after shipping over from Japan.
It has been a really great father daughter project. How wide are stock front sold axle pickup springs? I was filling the tank and checking the oil at a service station about 300 miles from home and I noticed that the coolant was empty. I thought those were 4x4 fenders on it. It was fixed as a running change in the 2005 model year. Better for manauvering around the camp site areas. He already had a 22re equipped one with 450,000km and it was getting tired. Perhaps the single most misunderstood axle term is reverse cut, often mistakenly referred to as reverse rotation.
One blinkers is taped on, cracked gril, crappy bumper, dented hood etc. At the minimum don't use different wheel back spacings or wheel spacers. I'd be a bit worried about a regular pickup axle being able to carry the weight. In addition to being used in these applications, the engine was also placed in the Toyota Hilux, Celica, and Corona, in addition to the Volkswagen Taro, which was essentially a re-badged Toyota Hilux. Upon removing the air plenum, I noticed a liquid in the bottom of two of the intake runners.