I do not know if you still need this information, but I am going ahead and answering it anyway. I have only been a free contributor to this site for the past 4-months. I am personally going back to answer your unanswered questions. The next step for 2004 Chevrolet Tracker serpentine belt replacement is simply removing the old belt from around the various pulleys. Once the 04 Chevrolet Tracker serpentine belt replacement is around the tension pulley, release the socket wrench and allow the tension pulley to take up the slack on the Automotive Serpentine Belt Replacement.
An old alternator doesn't provide the power to keep your electrical system going, which results in dim lights and a malfunctioning radio. The serpentine belt is located on the front of the engine block and winds around several pulleys driving various engine components: water, fuel and power steering pumps, the alternator, air conditioner compressor and possibly other accessories. Next, follow this link and watch the video that shows you how to replace a serpentine belt. This will show an illustration for the proper 2004 Chevrolet Tracker serpentine belt replacement route around the engine. An 2004 Chevrolet Tracker serpentine belt replacement too small will bind the pulleys while an 04 Chevrolet Tracker serpentine belt replacement too large will just fall off. Mar 29, 2011 1; remove neg. This will be the last Pulley that the belt will go on.
Attach the socket and set the direction to tighten the same direction the spring action allows the pulley to move. Then you will loosen alternator to let tension off fan belt and replace the fan belt. Check out some of my other posts if you need more tips and info. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them. Take the belt off the pulley and let it hang. Different engines require 2004 Chevrolet Tracker serpentine belt replacement belts of different widths, thicknesses and lengths or circumference.
Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys. Pick a Pulley that is most easily accessed. Standard Rules for Installing the Serpentine Belt: a. There is a tensioner that should put the proper amount of pressure on the belt assuming this has one serpentine belt. There is a good change the tension pulley will need to be moved farther for the 2004 Chevrolet Tracker serpentine belt replacement because the old belt may have stretched. This must be done correctly.
Find the tension pulley located at the bottom of the motor. Finding Tracker performance alternators doesn't have to be hard when you shop with AutoZone, as alternators play a crucial role in your Tracker's ability to run and perform. Again, use the socket wrench to turn the tension pulley far enough so the 04 Chevrolet Tracker serpentine belt replacement can be wrapped around the pulley. If the belt is broke, of course, this procedure for 04 Chevrolet Tracker serpentine belt replacement is not necessary but reversing the procedure is necessary 2004 Chevrolet Tracker serpentine belt replacement installation. It sounds simple I know, but looks dan be deceiving. Your Chevrolet Tracker is a unique blend of power and versatility with off-road capabilities. This pulley is attached to a very strong spring and holds the belt tight against the pulleys through its serpentine route around the engine.
Use a socket wrench with a matching socket the same size as the hex head bolt in the center of the tension pulley. . The repair is now complete. Turn the wrench handle, the pulley moves and the tension on the belt slackens. The new belt will need more clearance to get on the pulley. To see what kind of output you're currently getting, stop by your local store for a free battery charging and engine diagnostic testing today. This spring is pretty hard and with a new belt, it will be even harder to install.
See the Diagrams on Link 2. Remove the loosened belt off one of the other more easily accessed Pulleys. Once the 04 Chevrolet Tracker serpentine belt replacement is around the pulleys, allow the 2004 Chevrolet Tracker serpentine belt replacement to hang freely at the bottom of the engine. Posted on Mar 14, 2010 Jerald, You will have to remove the the accessory belt first I believe by putting appropriate wrench on tensioner and pulling tensioner toward passenger side to allow removal of the belt. This will usually be on top.
Make sure all pulleys have the belt routed to them the proper way. There may also be a diagram under the hood by the radiator. . . . . .
. . . . . .
. . . . . .